SmartLife LED Strip
Wi-Fi | Koel Wit / RGB / Warm Wit | SMD | 5.00 m | IP44 | 2700 - 6500 K | 960 lm | Android™ / IOS
Kenmerken
• Rode, groene en blauwe verlichting mogelijk, of een tint tussen warm- en koudwit - perfect aan je stemming aan te passen
• De lengte van 5 meter kan worden ingekort of verlengd - voor eindeloze mogelijkheden
• Dubbelzijde lijmstrip (3M) al aangebracht - voor gemakkelijke bevestiging
• Werkt als slimme standalone lamp - kan ook met andere SmartLife-producten worden gecombineerd om een complete slimme woning te creëren
Deze ledstrip combineert RGB en warm- en koudwit. Je kunt dus niet alleen je favoriete kleur instellen, maar ook warme of koude indirecte verlichting
De lengte van 5 meter kan worden ingekort of verlengd met vergelijkbare ledstrip, voor eindeloze mogelijkheden
De dubbelzijdige lijmstrip (3M) is al aangebracht voor gemakkelijke bevestiging op elk schoon en vlak oppervlak.
Verpakking
Inhoud verpakking
RGBW ledstrip (5 m)
WiFi-controller
Voeding
Snelstartgids
Verpakkingsafmetingen Cadeaubox met eurolock
Breedte | Hoogte | Lengte |
---|---|---|
50 mm | 190 mm | 185 mm |
Logistieke afmetingen
Verpakt per | Breedte | Hoogte | Lengte | Gewicht |
---|---|---|---|---|
1 | 182 mm | 50 mm | 210 mm | 420 g |
8 | 195 mm | 245 mm | 420 mm | 3720 g |
32 | 410 mm | 440 mm | 510 mm | 16000 g |
Productspecificaties
Breedte |
151 mm |
Hoogte |
8 mm |
Diepte |
5000 mm |
Gewicht |
310 g |
Ingangsvoltage |
220 - 240 V AC 50/60 Hz |
Maximale antenne versterking |
2.5 dBi |
Geschikt voor |
Nedis® SmartLife |
Kabellengte voedingsadapter |
1.50 m |
Maximaal zendvermogen |
16 dBm |
Kleurweergave-index (Ra) |
80 |
Lichtkleur |
Warm Wit Koel Wit RGB |
App beschikbaar voor |
Android™ IOS |
IP-codering |
IP44 |
Maximale stroomverbruik |
15 W |
Stekkertype |
Euro (CEE 7/16) |
Dimbaar |
Ja |
Ondersteunde draadloze technologie |
Wi-Fi |
Op maat te knippen |
Ja |
Energieverbruik per 1000 uur |
15 kWh |
Materiaal |
Siliconen |
Montage |
Wandmontage |
Verlengbare lichtstrip |
Ja |
Zendfrequentie |
2412 - 2484 MHz |
Aantal producten in verpakking |
1 Stuks |
Apparaat stroominput |
DC |
Nominale levensduur lamp |
20000 u |
Kleurtemperatuur |
2700 - 6500 K |
Energieklasse |
F |
Nominale lichtstroom |
960 lm |
Kleur |
Multicolour |
Lengte snoer |
5.00 m |
LED Type |
SMD |
LED-module |
SMD 5050 |
Aantal leds per meter |
90 Stuks |
Ondersteuning
Veelgestelde vragen
Kan ik meerdere personen toegang geven tot mijn SmartLife producten?
Ja dat is mogelijk.
Ieder persoon dient een account aan te maken in de SmartLife app.
Om deze personen toe te voegen als familie volg dan onderstaande stappen:
Klik linksboven op de naam van uw huis in het hoofdscherm.
Selecteer beheer huis, klik opnieuw op de naam van uw huis.
Hier ziet u uw instellingen van uw huis zoals aantal kamers, lokatie ect.
Klik hier daaronder onder de kop Familieleden op "Leden toevoegen".
Dit geeft de persoon toegang tot al uw SmartLife producten.
Wilt u een persoon alleen toegang geven tot 1 bepaald product, ga naar instellingen van het bepaalde product en selecteer "Apparaat delen" klik op toevoegen.
Mijn Smartlife producten verliezen iedere keer verbinding met mijn WIFI netwerk.
Dit is waarschijnlijk een wifi probleem die verschillende oorzaken kan hebben:
1.) Wifi signaal is instabiel
2.) Wifi signaal is te zwak
3.) Using an access point with the same SSID and Password that do not support IEEE802.11R standaard.
Probleem 1 kan vaak opgelost worden door uw router te herstarten.
Probleem 2 kan worden opgelost door een met een app Wifi analyzer uw signaal te controleren en eventueel om van kanaal op uw router in te stellen.
Probleem 3 Dit kunt u controleren door acces points en versterkers uit te schakelen. Als de producten dan weer online komen dan zijn de acces points en versterkers een probleem. We raden u dan aan om een Mesh systeem te gebruiken die de IEE802.11R ondersteunen (wifi6)
Wij hebben voor u de volgende vragen gevonden in het Engels
Can the strip light up in multiple colours at the same time?
No, the LED's are not individually addressable.
My LED strip does not want to install with the EZ mode installation.
Please try the AP mode.
Make sure that you use a 2.4Ghz wifi network.
Reset the controller so the LED strip blinks slow. (press and hold the button on the controller)
If it blinks fast, reset it again and it will blink slowly
In the app:
+ > [your device] > tap on EZ mode and select AP mode > confirm it was reset > fill in the info of your wifi network > follow the steps in the app.
Hold your phone very close to the plug during the installation
This method uses a direct connection to the device to send the info of your wifi to it.
Holding it close optimises this connection
Can I just take the adhesive strip off?
Ensure that you only take off the plastic protection and not the entire adhesive strip.
If you remove the whole strip, you will not be able to stick it to anything.
Can I extend the strip?
Yes, you can purchase another set and plug the second strip in the first one.
If you extend it to 10m (5m extra) then you might see some loss in brightness at the end of the second strip.
We recommend you install multiple complete sets and group them in the app.
Now you can control all of the strips as if they are a single strip without any loss in brightness.
Can I give other people access to my Smartlife devices too?
Yes you can.
Each person needs a unique account on their mobile device.
To add them as "family members" follow these steps:
In the main screen of the app tap on the name of your home (top left)
Tap on Home management
Tap on the name of your home again.
Tap on "add family members" and fill in the account details of the person you want to add.
It will give them access to all the devices in your home as a normal member or admin (you can select this)
If you only want to share a single device in a home, go to the settings menu of the device and select "share device" -> add member.
My Smartlife products lose the Wifi connection every time.
This is probably a Wifi problem, this can be for various reasons.
1.) Wifi signal is unstable.
2.) Wifi signal is too weak.
3.) Using an access point with the same SSID and password that do not support the IEEE 802.11R standards.
Problem 1 can often be solved by restarting the router.
Problem 2 can be checked with an app Wifi analyzer with this the signal can be viewed and corrected to a better position.
Problem 3 can be checked as the access points are turned off, the Wifi signal is still good and the connection remains if the access points are a problem, a Mesh solution can then be used.
Please make sure that they support IEEE 802.11R standard.